MBEPOXY® resin systems for art projects are available in both 2:1 and 3:1 mixing ratios by weight, depending on the specific product selected.

The correct ratio must always be taken from the label or technical instructions of the exact MBEPOXY® resin you are using. The standard MBEPOXY® Art Resin, designed for approximately 2–3 mm artistic pours, uses a 2:1 ratio by weight—two parts resin to one part hardener. For example, to prepare 300 grams of mixed material, measure 200 grams of resin and 100 grams of hardener.

Some MBEPOXY® systems used by resin artists are supplied in a 3:1 ratio by weight. These include products intended for thicker applications, such as Eon Multipurpose Resin and Table Top Resin. In a 3:1 system, a 400-gram batch would require 300 grams of resin and 100 grams of hardener.

Artists should never assume that every MBEPOXY® product uses the same ratio. Do not mix a 2:1 resin with the hardener from a 3:1 system, and do not estimate quantities by eye. Use a reliable digital weighing scale, measure each component accurately and mix slowly while scraping the sides and bottom of the cup. MBEPOXY® also advises following the formulation-specific ratio because incorrect measurement can lead to sticky surfaces, incomplete curing, softness or reduced durability.

For the most consistent result, identify the project type first- thin resin art, coating, multipurpose casting or tabletop work and then choose the matching MBEPOXY® grade and follow the ratio printed on that product.

MBEPOXY® art resin takes approximately 12 hours or 24 hours to cure completely, depending on the specific resin formulation selected.

MBEPOXY® offers different resin systems for different types of creative work, so artists should always check the curing time printed on the label of the exact product being used. The standard MBEPOXY® Art Resin Kit has a full internal cure time of approximately 10–12 hours at 25–30°C, making it suitable for artists who need a comparatively faster curing option for coasters, trays, wall art, geodes and layered resin projects.

Other artist-friendly systems, including MBEPOXY® Eon Multipurpose Resin and Table Top Resin, generally require approximately 24 hours for a full cure under normal room-temperature conditions. These slower-curing options provide more working time and are suitable for thicker pours, tabletops, decorative castings and projects where additional levelling or bubble release is required.

Curing time can vary according to room temperature, humidity, pour thickness, batch quantity and mixing accuracy. Cold or rainy conditions may slow the curing process, while an incorrect resin-to-hardener ratio may leave the project soft, sticky or partially uncured. Artists should measure both components accurately by weight, mix thoroughly and keep the project in a clean, dust-free and level area while it cures.

Even when the surface feels dry, avoid demoulding, sanding, drilling, packing or placing heavy objects on the artwork too early. For best results, follow the exact curing time stated for the selected MBEPOXY® grade and allow additional time when working in cooler conditions or making thicker pieces.

Yes, MBEPOXY® Art Resin is beginner-friendly and can be used for a first resin art project when the correct mixing ratio, safety precautions and curing instructions are followed.

Beginners can start with simple projects such as coasters, keychains, bookmarks, small trays or abstract resin boards. These projects require manageable quantities of resin and help new artists understand measuring, mixing, colouring, pouring and bubble removal before attempting larger or more detailed designs. MBEPOXY specifically recommends starting with small projects to build confidence and learn how resin behaves.

The MBEPOXY® Art Resin Kit is formulated for artists and hobbyists and offers self-levelling flow, bubble-release properties, clear transparency and a high-gloss finish. The kit uses a 2:1 resin-to-hardener ratio by weight, so beginners should use a digital weighing scale instead of estimating the quantities by eye.

For the best result, prepare the workspace before mixing. The table should be level, clean and protected, and all moulds, pigments, cups and mixing sticks should be ready. Mix slowly and thoroughly while scraping the sides and bottom of the cup. Incorrect ratios, rushed mixing, dust and touching the piece before it cures are among the most common beginner mistakes.

Always wear gloves and work in a well-ventilated area. MBEPOXY describes its artist resin as suitable for beginners when proper safety precautions are followed.

By beginning with a small project, following the exact product ratio and allowing sufficient curing time, a first-time artist can achieve a smooth, glossy and attractive result with MBEPOXY® Art Resin.

It is crystal clear, with a shelf life of 12 months from the manufacturing date. However, prolonged UV exposure may cause yellowing over time.

MBEPOXY® Art Resin is designed to provide a clear, glossy base that allows pigments, mica powders, embedded flowers, photographs, glitter and decorative elements to remain visible after curing. Its clarity makes it suitable for resin jewellery, coasters, trays, artwork, encapsulation projects and other small-format crafts where the transparency of the finished piece is important. The official product information describes MBEPOXY® Art Resin as offering exceptional clarity and a crystal-clear base for artistic work.

However, crystal clear does not mean that any epoxy resin will remain completely unchanged under every condition forever. Continuous exposure to direct sunlight and ultraviolet rays can gradually affect clear epoxy and may cause a yellow or amber tint. MBEPOXY guidance also identifies sunlight and UV exposure as common reasons why clear resin may yellow over time.

Resin artists can help preserve clarity by keeping finished pieces away from prolonged direct sunlight, extreme heat and harsh outdoor exposure. This is especially important for transparent projects, white backgrounds, preserved flowers and light pastel designs, where even a slight colour change may be more noticeable.

The unused resin has a shelf life of 12 months from the manufacturing date. Always check the manufacturing date before use and keep the resin and hardener in their original, tightly sealed containers. Following the correct mixing ratio, mixing thoroughly and allowing the project to cure in a clean, protected area will help MBEPOXY® Art Resin deliver a smooth, clear and high-gloss finish.

MBEPOXY® Art Resin is designed for creative artwork and thin coating projects, while Doming Resin is formulated to create a raised, thick and glossy dome over small surfaces.

MBEPOXY® Art Resin is the most versatile choice for projects such as resin paintings, coasters, trays, geodes, wall art, jewellery components and other decorative crafts. It has self-levelling flow, crystal-clear transparency and a high-gloss finish, allowing it to spread smoothly across a flat surface. The standard MBEPOXY® Art Resin is intended for pours of approximately 2–3 mm, making it suitable for coating artwork, adding pigments and creating flowing decorative effects.

Doming Resin has a higher viscosity, which means it is thicker and does not spread as freely as Art Resin. It is designed to stay within the edges of a small item and naturally form a smooth, rounded dome. This makes it suitable for labels, decals, badges, pendants, keychains, stickers, logos and other small decorative surfaces where a raised, glass-like finish is required.

MBEPOXY® offers different Doming Resin options, including flexible and hard-curing formulations. Flexible Doming Resin remains slightly bendable after curing, helping reduce cracking or peeling on curved or flexible items. Hard Doming Resin is more appropriate where a firm, rigid dome is required.

Resin artists should select the product according to the desired result. Art Resin is better for broad creative surfaces and coating work, while Doming Resin is better for controlled, raised finishing on smaller pieces. Using Art Resin for doming may cause it to flow over the edges, while using thick Doming Resin for large artwork may make spreading and levelling more difficult.

Yes, MBEPOXY® Art Resin can be used for making resin coasters and jewellery.

MBEPOXY® Art Resin is formulated for artists and hobbyists who create decorative resin projects. Its crystal-clear appearance, self-levelling flow and high-gloss finish make it suitable for coasters, pendants, earrings, bracelets, keychains and other small resin-art pieces. The clear base also allows compatible pigments, mica powders, glitter, dried flowers and decorative inclusions to remain visible inside the finished work.

For coaster-making, Art Resin works well for thin pours and surface coatings. The standard MBEPOXY® Art Resin is recommended for pours of approximately 2–3 mm, so deeper coaster moulds may need to be completed in multiple layers or made using a resin grade intended for thicker casting. Artists should follow the mixing ratio printed on the selected product and avoid exceeding its recommended pour depth.

For jewellery, the resin can be poured into suitable silicone moulds or used as a clear coating over small decorative pieces. Mix slowly to reduce bubbles, scrape the sides and bottom of the mixing cup, and add pigments or inclusions only after the resin and hardener have been combined thoroughly. Small jewellery moulds require careful pouring so that fine details and narrow sections are completely filled.

Allow every piece to cure fully before demoulding, sanding, drilling or attaching jewellery findings. Premature handling may leave fingerprints, bends or surface marks. For slightly thicker coasters or small cast jewellery, MBEPOXY® Eon Resin is another available option designed for casting depths of approximately 8–10 mm.

By selecting the correct MBEPOXY® resin for the project thickness and following the recommended mixing and curing instructions, both beginners and professional resin artists can create glossy, clear and attractive coasters and jewellery.

The amount depends on the canvas size and coating thickness; measure the length, width and desired resin depth using the MBEPOXY® Resin Volume Calculator, then prepare about 10% extra for edges and normal wastage.

For resin canvas painting, the required quantity is determined by the total surface area rather than by one fixed amount for every artwork. A small canvas needs considerably less resin than a large geode or abstract-art panel, and a thin glossy coating requires less material than a heavier flowing design. MBEPOXY recommends calculating the artwork’s dimensions before mixing so that the complete surface can be covered in one continuous pour.

As a planning example, a 1/16-inch coating would require approximately:

• 12 × 12-inch canvas: about 150 ml of mixed resin
• 16 × 20-inch canvas: about 330 ml
• 24 × 36-inch canvas: about 885 ml

These are volume-based estimates for a consistent 1/16-inch layer. Add approximately 10% extra for drips, cup residue, edges and spreading losses. The exact weight in grams may vary slightly according to the selected resin system, so use the correct MBEPOXY® resin-to-hardener ratio printed on the product.

Resin artists should also check that the canvas is strong and tightly stretched. A large amount of resin can collect in the centre and cause a flexible canvas to sag. Supporting the underside with a firm board or using a rigid art panel, can help maintain an even surface. Place the canvas on raised cups, confirm that it is completely level and tape the underside edges to make cured drips easier to remove. MBEPOXY® specifically recommends elevating and levelling the artwork before pouring.

Prepare all colours and tools before mixing, and make the full required quantity at once whenever possible. Mixing a second batch midway may create visible lines, uneven curing or colour differences.

No, UV lamp is not required. MBEPOXY® Art Resin self-cures after the resin and hardener are mixed correctly.

MBEPOXY® Art Resin is a two-component epoxy system. Once the resin and hardener are combined in the correct ratio and mixed thoroughly, a chemical curing reaction begins automatically. The project should then be left on a clean, level surface at normal room temperature until it becomes fully hard. The MBEPOXY® Art Resin Kit lists an approximate full internal cure time of 10–12 hours at 25–30°C, although the exact time may vary with the selected formulation and working conditions.

This is different from UV resin, which is generally a single-component material that requires ultraviolet light to harden. A UV lamp should not be necessary for MBEPOXY® Art Resin, and exposing the project to concentrated UV light will not correct an inaccurate mixing ratio or incomplete mixing.

For reliable self-curing, resin artists should measure both components accurately according to the ratio printed on the product label, mix slowly while scraping the sides and bottom of the cup, and pour within the available working time. The artwork should remain protected from dust, water, movement and accidental contact during curing.

Temperature is also important. Cooler or rainy conditions may slow the reaction, while excessive heat can shorten the working time. Avoid placing the project in direct sunlight or using strong external heat to force a faster cure. If the resin remains soft or sticky beyond the expected curing period, the likely causes include an incorrect ratio, insufficient mixing or unsuitable temperature rather than the absence of a UV lamp.

When prepared correctly, MBEPOXY® Art Resin cures independently and develops a clear, self-levelled, high-gloss finish without special lighting equipment.

You will need a digital weighing scale, mixing cups, wooden stirring sticks, a silicone spatula, a heat gun or torch and suitable silicone moulds or a prepared art surface.

A digital weighing scale is one of the most important tools for working with MBEPOXY® Art Resin because the resin and hardener must be measured accurately by weight. The selected product may use a 2:1 or 3:1 mixing ratio, so estimating the quantities by eye can lead to soft, sticky or incompletely cured artwork.

Use clean mixing cups that are large enough to hold the complete batch without overflowing. Wooden stirring sticks help combine the resin and hardener, while a silicone spatula is useful for scraping material from the sides and bottom of the cup. Stir slowly and thoroughly to achieve a uniform mixture without introducing excessive air bubbles.

A heat gun or small torch can help remove bubbles that rise to the surface after pouring. Use heat briefly, keep the tool moving and avoid holding it too close to the resin. Excessive heat can damage silicone moulds, disturb pigments or cause ripples and premature curing.

Choose silicone moulds for making coasters, jewellery, keychains, trays and similar cast pieces. For resin paintings or coating projects, use a level canvas, MDF board, wooden panel or another properly prepared art surface.

Resin artists should also keep disposable gloves, table-protection sheets, paper towels, pigments, measuring containers and a dust cover ready before mixing. Work on a completely level surface in a clean and well-ventilated area. Preparing every tool in advance is important because the usable working time begins as soon as the MBEPOXY® resin and hardener are mixed.

Yes, compatible pigments and resin-grade glitter can be mixed directly into MBEPOXY® Art Resin.

MBEPOXY® Art Resin is designed to work with a wide range of epoxy pigments, powders, colourants and decorative materials, making it suitable for coasters, trays, jewellery, geodes, wall art and other creative resin projects. Its crystal-clear base helps pigments appear vibrant and allows glitter to retain its sparkle after curing.

For the most reliable result, first measure the resin and hardener accurately according to the ratio printed on the selected product. Mix both components thoroughly, scraping the sides and bottom of the cup. Once the mixture is uniform, add the pigment or glitter gradually and stir slowly until it is evenly distributed. This method helps prevent unmixed material, colour streaks and glitter clumps.

Use only pigments that are compatible with epoxy resin. MBEPOXY® pigments are designed for resin-art applications and can be blended to create customised shades. Avoid water-based paints, poster colours or unknown liquid colourants because unsuitable additives may introduce moisture or interfere with proper curing.

For glitter effects, use fine or chunky resin-compatible glitter according to the desired design. Fine glitter generally disperses more evenly, while heavier glitter may gradually settle in low-viscosity resin. Resin artists can create layered effects by pouring a clear layer, adding glitter and sealing it with another clear coat. Do not overload the mixture, as excessive glitter may make the resin difficult to pour and can affect its curing behaviour.

Prepare a small test batch before working on the final project. This allows you to check the colour strength, glitter distribution, transparency and cured appearance before mixing a larger quantity.

Your resin may remain tacky after 24 hours because of an incorrect 2:1 mixing ratio, inaccurate measurement, incomplete mixing, low temperature, high humidity or an excessively thick pour.

For standard MBEPOXY® Art Resin, the resin and hardener must be measured accurately in a 2:1 ratio by weight. Even a small measuring error can prevent the two components from reacting properly, leaving the artwork soft, sticky or unevenly cured. Always use a digital weighing scale rather than estimating the quantities by eye or relying on unmarked cups.

Improper mixing is another common cause. Stir the resin and hardener slowly and thoroughly, scraping the sides, bottom and corners of the cup. If unmixed material remains on the cup walls and is scraped onto the artwork during pouring, those areas may stay tacky even when the rest of the piece cures correctly. MBEPOXY guidance identifies inaccurate ratios and poor mixing as common reasons for incomplete curing.

Temperature and humidity also affect curing. A workspace below approximately 20–25°C, cold resin bottles or high humidity can slow the chemical reaction. Keep the project in a clean, dry and stable environment and allow additional curing time during cold or rainy weather. MBEPOXY® notes that temperature, humidity and moisture can significantly affect curing performance.

Do not apply extra hardener directly over a tacky surface, as this will not correct the original mixture. If the resin is only slightly tacky, allow another 12–24 hours in suitable conditions. If it remains liquid, gummy or sticky throughout, the incorrectly cured material may need to be removed before applying a freshly measured and thoroughly mixed MBEPOXY® coat. For future projects, prepare a small test batch and remain within the recommended pour thickness.

Use a heat gun or small torch lightly over the freshly poured resin to bring trapped air bubbles to the surface and pop them.

After pouring MBEPOXY® Art Resin, allow the mixture to settle briefly so that trapped air can begin rising naturally. Then pass a heat gun on a low setting or a small torch quickly over the surface. Keep the heat source moving continuously and maintain a safe distance from the resin. The purpose is to warm only the surface slightly, not to heat the entire artwork. This controlled heat helps trapped bubbles rise and burst before the resin starts curing. MBEPOXY recommends using a heat gun or torch lightly after pouring for a cleaner, bubble-free finish.

Do not hold the heat gun or flame over one area for too long. Excessive heat can disturb pigments, create waves, accelerate curing or damage the finished surface. Several quick passes are safer than one long application. Stop using heat once the resin begins becoming thick or tacky because disturbing it at that stage may create marks rather than improve the finish.

Bubble prevention should begin during mixing. Stir the resin and hardener slowly instead of whipping the mixture, and scrape the sides and bottom of the cup carefully. Fast mixing, excessive stirring, cold resin and air released from porous surfaces can all increase bubble formation. Sealing porous wood or similar materials before the main pour can also help reduce trapped air.

MBEPOXY® Art Resin includes bubble-release agents that help push trapped air towards the surface, making bubbles easier to remove. Combining this formulation with slow mixing and controlled heat helps resin artists achieve a clearer, smoother and more professional finish.

Yes, MBEPOXY® Art Resin is suitable for everyday items such as coasters and decorative trays once it has been mixed correctly and allowed to cure completely.

MBEPOXY® Art Resin is formulated for home-based resin art and craft projects, including coasters, trays, jewellery, wall art and other decorative items. Its crystal-clear appearance, self-levelling flow, scratch resistance and high-gloss finish help artists create functional pieces that look smooth and professionally finished. The product is also described as suitable for home use when used in a well-ventilated workspace.

For safe and reliable everyday use, measure the resin and hardener accurately according to the ratio printed on the product, mix thoroughly and allow the item to cure for the full recommended period. Do not use the coaster or tray while the resin is still soft, flexible, tacky or giving off an uncured smell. Premature use can leave cup marks, fingerprints or dents on the surface.

It is important to separate general household use from direct food contact. A decorative tray can be used for serving packaged items, cups or other objects, but food should not be placed directly on the cured resin unless the particular product is specifically labelled and approved as food-safe. MBEPOXY guidance recommends checking for a food-safe label whenever the finished item will come into direct contact with food, utensils or drinking surfaces.

Very hot cookware should also not be placed directly on resin items unless the selected formulation is rated for that temperature. Using coasters for normal cups and glasses is appropriate, but a small heat-resistant mat is advisable for extremely hot vessels. When the correct MBEPOXY grade is selected and fully cured, it provides resin artists with a clear, attractive and durable finish for everyday coasters and trays.

The shelf life of unopened MBEPOXY® resin and hardener bottles is 12 months from the manufacturing date when stored correctly.

To maintain product quality throughout this period, keep both bottles tightly sealed in their original containers and store them in a cool, dry place away from direct sunlight, moisture and excessive heat. The resin and hardener should remain separate until you are ready to begin your project. Do not transfer them into unlabelled containers, as this may cause contamination, confusion between components or loss of important manufacturing and batch information.

For resin artists, proper storage is especially important because temperature and moisture can affect the clarity, flow and curing performance of the material. Avoid keeping the bottles near windows, ovens, heaters or damp areas. After purchasing the resin, check the manufacturing date printed on the packaging so you can use the product within the recommended 12-month period.

Even when the bottles are unopened, inspect the material before use. The resin and hardener should match their normal appearance and should not contain visible contamination caused by damaged packaging. If a bottle has leaked, the seal is broken or the material appears unusual, contact the MBEPOXY® team before using it in an important artwork.

Once opened, close the caps immediately after measuring the required quantity. Never return leftover mixed or poured material to the original bottle, as this can contaminate the remaining product. Using clean tools and storing the bottles properly helps preserve the MBEPOXY® Art Resin’s clarity, mixing performance and curing quality for future coasters, trays, jewellery and other resin-art projects.

Yes, MBEPOXY® Art Resin can be applied to wood, canvas, MDF, artboards and other properly prepared craft surfaces.

Its strong adhesion, self-levelling flow and high-gloss finish make it suitable for resin paintings, geode art, ocean art, wooden wall décor, serving trays, plaques, frames and mixed-media projects. MBEPOXY® identifies wood, canvas, silicone moulds and MDF among the common surfaces used for resin-art and DIY applications.

The surface must be clean, dry, level and free from dust, oil, grease, loose paint or flaky material. For wooden projects, sand rough areas and remove all sanding dust before pouring. Because unfinished wood can release trapped air and absorb resin unevenly, applying a thin sealing coat first can help reduce bubbles and dark patches. Any cracks, knots or holes should also be sealed before the main decorative pour.

Canvas can be used for resin paintings, but it should be tightly stretched and firmly supported from underneath. Resin adds weight, so an unsupported canvas may sag in the centre and cause the mixture to collect unevenly. Place the canvas on a perfectly level work surface and raise it slightly so excess resin can flow cleanly over the edges. MBEPOXY® also lists canvases, artboards and tiles as suitable surfaces for epoxy artwork.

Measure the resin and hardener according to the ratio stated for the selected MBEPOXY® product, mix thoroughly and pour within its working time. Applying the resin to a properly prepared surface helps prevent poor adhesion, uneven coating, trapped bubbles and sticky areas while producing a clear, glossy and professional-looking finish.