Most people don’t plan to buy epoxy for their table. They plan to fix it. A stain that won’t come off, a scratch that catches the light, a top that has lost its shine. Then one day they search for a fix and land on table top epoxy.
It’s a good fix. Table top epoxy covers the damage, protects the wood and gives the table a clear, glossy top. The part that confuses people is the choice: 8-10 mm or 18-20 mm, and how much to buy. This guide sorts that out.
What is Table Top Epoxy?

Table top epoxy is a thick, clear resin you pour over a wooden or other surface. It spreads out, levels itself and sets into a hard, smooth layer. It works on dining tables, study tables, coffee tables, counters and bar tops. A good table top epoxy resin stays clear, handles light scratches and doesn’t mind water rings.
8-10 MM Table Top Resin: When To Pick It
The table top resin 08-10 mm is made for flat coatings and thin pours. Pick it when:
-
You want a glossy finish over a plain wooden or veneer top
-
You’re sealing and protecting an old table
-
You’re coating a desk, counter or cafe table
-
Your pour is up to about 10 mm deep
For a regular resin table top with a clean, simple look, this is the practical choice.
18-20 MM Deep Cast: When To Pick It
The table top deep cast resin 18-20 mm is made for thick pours. Pick it when:
-
You’re building a river table with a wide gap
-
You want to fill deep cracks, knots or live edges
-
You’re casting a thick block or slab
-
You need 18 to 20 mm in a single pour
A deep casting epoxy resin cures slowly, which keeps heat low and stops cracks and yellowing. A thin-pour resin used in a deep pour can overheat, so always match the resin to the depth.
Quick comparison
|
Point |
8-10 mm resin |
18-20 mm deep cast |
|
Best for |
Flat coating, thin pours |
River tables, deep fills |
|
Pour depth |
Up to 10 mm |
18 to 20 mm |
|
Curing speed |
Faster |
Slower |
|
Typical use |
Table tops, counters, desks |
Live edge, thick castings |
How Much Resin Do You Need?
This is where most people get stuck, but the maths is short:
Length (m) × Width (m) × Thickness (mm) = Litres of resin
Example 1: A dining table of 1.8 m × 0.9 m with a 3 mm coat needs 1.8 × 0.9 × 3 = about 4.9 litres.
Example 2: A river channel of 1.2 m × 0.2 m, 20 mm deep, needs 1.2 × 0.2 × 20 = about 4.8 litres.
Add 10% extra for spills, edges and what sticks to the mixing cup. If the wood has deep cracks or knots, add a bit more. Running short halfway through a pour is a bad day, so it’s better to have a little left over.
Steps For Epoxy On Table Top
-
Level the table: Use a spirit level, because an uneven table gives an uneven coat.
-
Clean and sand: Remove dust, oil and old polish.
-
Seal the wood: A thin seal coat stops air bubbles from rising out of the wood.
-
Block the edges: Use tape or a frame to hold the resin in.
-
Mix well: Follow the ratio on the label and stir slowly for 3 to 5 minutes.
-
Pour and spread: Pour from the centre and let it flow. Use a spreader at the edges.
-
Remove bubbles: Pass a heat gun quickly over the surface.
-
Cover and cure: Keep dust away for 24 to 72 hours.
Doing epoxy on table top in a clean, warm room makes a big difference to clarity.
Mistakes To Avoid
-
Using a thin-pour resin for a deep pour
-
Skipping the seal coat on wood
-
Pouring in a cold or damp room
-
Measuring by eye and not by cup
-
Working on an uneven table
-
Touching the surface before it sets
How To Choose Where To Buy
When you compare epoxy resin suppliers in India, check that the pour depth is clearly stated, the mixing ratio is given and someone can answer your quantity questions. If you’re looking for the best resin brand in India for your project, look at clarity, cure time and whether the product matches your table. A resin that fits your project matters more than a big name.
Ready to pour?
Pick the depth that suits your table and order your table top epoxy from MBEPOXY. Measure once, add 10%, and you’re set.
FAQs
1. Is the difference between 8-10 mm and 18-20 mm table top epoxy?
The 8-10 mm resin is for thin coats and flat finishes. The 18-20 mm deep cast is for thick pours like river tables.
2. How do I calculate resin for my table top?
Multiply length (m) by width (m) by thickness (mm). The answer is in litres. Add 10% extra.
3. Can I use table top epoxy resin on an old wooden table?
Yes. Sand it, clean it and apply a seal coat first.
4. How long does epoxy on table top take to cure?
It sets in 24 to 72 hours. Full strength takes about a week.
5. How do I pick from epoxy resin suppliers in India?
Check pour depth, mixing ratio, clarity and the help offered for your project size.
6. Can I pour 20 mm of regular resin in one go?
No. Use a deep cast resin, as thin-pour resin can overheat and crack.

